Hardeman Motorsport B.V. — Zandweg 20a, Kruiningen (NL) +31 (0)113 700266 info@hardemanmotorsport.nl

What Additional Parts Do I Need When Replacing Drivetrain or Suspension Components?

We stock a wide range of components in our webshop, and having a clear checklist helps ensure you have every part on hand before starting a job. These are general checklists; specific vehicle models may require additional or fewer parts depending on their exact technical layout and condition.

What parts do I need when replacing components — Hardeman Motorsport

Clutch and flywheel:

Replacing your clutch or flywheel is a substantial job, and your car will be completely off the road until the work is completed. Typically, several assemblies must be removed first, including:
Exhaust system, heat shields, propeller shaft, and gearbox. Make sure you also have replacement hardware and consumables such as gaskets ready beforehand.

Consider the following components when replacing your clutch or flywheel:

  • Flywheel
  • Flywheel bolts, preferably fitted with threadlocker / Loctite (single-mass lightweight flywheels often require shorter bolts than a dual-mass flywheel (DMF))
  • Clutch friction disc and pressure plate
  • Pilot bearing (spigot bearing)
  • Clutch alignment tool, particularly essential for multi-plate clutches
  • Clutch release fork and release bearing, sensible to renew while the bellhousing is already off.
  • Pivot pin
  • New gearbox bellhousing bolts—if the clutch has been removed several times before, these bolts may be due for replacement, and having spares prevents delays if one goes missing.
  • Gearbox oil, since the gearbox is already removed
  • Gearbox mounts, as these will likely be unbolted during removal anyway.
  • Flex disc / Giubo coupling (especially if fitted between the gearbox output flange and propeller shaft)
  • Exhaust gaskets.
What parts do I need when replacing suspension components — Hardeman Motorsport (2)

Shock absorbers and springs or coilover suspension

Fitting shock absorbers, springs, or coilover suspension can easily take half a day to a full day of workshop time. Penetrating oil (such as WD-40) and copper grease are well worth having on hand, as suspension hardware is constantly exposed to moisture and road debris. The wheels will need to come off, and ABS sensors or brake hoses are often routed across the strut body, so having replacements on standby is sensible should anything be seized. This is also a practical opportunity to fit new brake pads or discs at the same time.
Using a proper spring compressor is strongly recommended whenever working on coil-over-strut assemblies.

Consider the following components when replacing shock absorbers and springs:

  • Shock absorbers (dampers)
  • Springs
  • Spring perches or spring isolators (rubber spring pads)
  • Top mounts and gaskets (mounting bracket, adapter, or adjustable camber plate for the damper)
  • Anti-roll bar drop links
  • Wheel bearings (where the hub carrier / upright is integrated with the strut)
What parts do I need when replacing brakes — Slotted big brake kit red 6-piston caliper

Brakes

Brake work is generally straightforward and manageable even for less experienced mechanics. Bear in mind that whenever brake hoses or hydraulic lines are disconnected, the brake system must be bled thoroughly—a task made far easier with a proper brake bleeding kit. Keep copper grease and penetrating oil (WD-40) ready, as brake hardware is heavily exposed to heat and corrosion.

Consider the following components when servicing or replacing brakes:

  • Brake discs
  • Brake pads and retaining clips / pins
  • Brake hoses (braided or OEM)
  • Caliper guide pins / slider bushes (for floating / two-piece brake calipers)
  • Caliper pistons and dust/pressure seals
  • Brake fluid
  • Wheel bolts / wheel studs and nuts (as the wheels must be removed for this job)
What parts do I need when overhauling subframe and control arms — Hardeman Motorsport (4)

Subframe and control arms

Overhauling a subframe and control arms involves several important specification choices; for detailed guidance on materials and bushing types, see our technical advice page: Subframe, control arm and engine mount bushings: which ones to choose? – Hardeman Motorsport.
Removing and installing press-fit subframe / control arm bushings usually requires dedicated extraction tools or a hydraulic workshop press, as original bushings can be seized tight in their housings. When rebuilding a complete subframe assembly with all control arms, printing out an exploded axle diagram is a practical way to verify that every single bushing is accounted for. With the subframe dropped, this is also the ideal time to replace corroded hard brake lines that are otherwise difficult to access.

Consider the following components and tasks when overhauling your subframe and control arms:

  • Subframe bushings
  • Subframe reinforcement plates, rust-removal supplies, and chassis paint / protective coating materials
  • Control arm bushings or spherical bearings (Uniballs) / ball joints
  • Differential, gearbox, or engine mount bushings
  • New bolts and locknuts for the subframe, differential, control arms, propeller shaft, and halfshafts / driveshafts
  • Anti-roll bar bushings and drop links.
  • Hard brake lines, handbrake cables/shoes, and flexible brake hoses
  • The exhaust system will likely need to be removed and refitted—ensure you have fresh mounting hardware and gaskets on hand.
  • Differential oil or gearbox oil (an ideal time to renew)
  • Full four-wheel geometry alignment

Need advice or a quote for your differential or chassis?

Send us your VIN and intended use for a tailored workshop quote, or order parts directly at Motorsportparts.nl.